High Pressure Grinding Mill

You are here: Home > Products > High Pressure Grinding Mill
Tip: If you would like more information about this product, or consult our product quotation, you can leave us a message at the bottom of the page( or click send inquiry directly to the bottom). We will get in touch with you within one business day, your message content will be strictly confidential.

Brief introduction to Hongxing high pressure grinding mill

High pressure grinding mill is suitable for high fine milling processing of non-flammable and non-explosive materials with Mohs hardness less than 9.3 and humidity below 6% such as barite, limestone, ceramic, slag; its finished product size ranges within 80-425 mesh. If equip with special device inside the machine, it can produce coarse powder with 30-80 mesh.

Performance characteristics of barite grinding mill

1. Three-dimensional structure, small footprint, complete sets; it forms independent production system from block materials to finished powder.
2. The fineness of finished power is even with rate of passing sieve 99%, which is other milling equipment cannot compare with.
3. Machine transmission device adopts enclosed gear box and belt wheel with smooth transmission and reliable operation.
4. Important parts are all made of high quality steel and high-performance wear-resistant materials, so that the whole machine has high wear-resisting performance and reliable operation.
5. The electrical system adopts centralized control, milling workshop basically achieve unattended operation with convenient maintenance.

Powder Making Plant

Working principle of dolomite grinding mill

Inside the host of high pressure grinding mill, a high pressure spring with 1000-1000 kg pressure is tightened on roller hanger.
In the working process, grinder roll rotates around principal axis, and appresses the ring rolling under the effects of high pressure spring and centrifugal force so that its pressure is 1.2 times higher than that of Raymond mill under the condition of same power.



When the materials to be ground enter into grinding chamber, they are scooped up by shovel knife and sent between grinding roller and grinding ring for grinding, then powders are taken in analytical engine along with the recirculating air; qualified fine powders flow into whirlwind powder collector along with the gas and become finished product, meanwhile, large particle materials fall back for re-grinding.

High Pressure Grinding Mill

Note

1.In working process, all doors must be completely closed. Set appropriate lighting device in the upper and lower sections as well as inspection door. If it happens failure while working process, please stop machine immediately to eliminate faults. If defect cannot be immediately eliminated, but without great impact on the work, operator should keep record.
2. Operator should frequently check the working state of various parts, but any cleaning and repair is absolutely prohibited carrying out in operation process of the machine. Spiral tensioning device in lower sector should be adjusted to keep it normally work.
3. High pressure grinding mill must start up under no-load condition and stop after unloading materials.

Parameters
     Parameter
Model
Raymond mill62 High strength66 High strength76 High strength87 High strength92 High strength93 High strength97 Raymond mill4119 Raymond mill4525
Feeding 
size(mm)
<15 <15 <20 <25 <25 <25 <25 ≤25 ≤30
Size of finished 
product(mm)
0.173-0.033 0.173-0.033 0.173-0.033 0.173-0.033 0.173-0.033 0.173-0.033 0.173-0.033 0.173-0.044 0.173-0.044
Shift output of
 different material 
fineness(t)
0.6-9 1-20 1.5-25 2.8-33 3-36 3.5-40 4-52 8-78 16-176
Rotate speed 
of central 
shart(r/min)
274 190 170 161 148 140 130 105 82
Diameter of 
pulverizing 
ring(mm)
525 725 850 907.5 973 1006 1050 1400 1770
Diameter of 
pulverizing 
ring(mm)
150 210 250 270 300 300 310 410 450
Height of
 pulverizing 
roller(mm)
100 150 150 150 160 160 170 190 250
Main Motor(kw) 7.5 15 18.5 22 30 30 37 75 132
Fan Motor 4-5.5 4-11 4-15 4-18.5 4-22 2-22 4-37 4-75 4-132
Analyzer Motor 6-1.1 6-2.2 6-2.2 6-2.2 6-2.2 6-3 4A-5.5 4B-7.5 4A-18.5

Quick Way To Get Price

Please feel free to fill in the following form or email us (sales@hxjq.com) to get product information,price,service and other supports.We will reply to you within 24 hours as soon as possible.Thank You!

*

*

Copyright© 2018 hongxing machinery.All rights reserved